金穗（Kingsui） TPU 2790 KISUANE物性表
金穗 聚酯型TPU 400系列
| 聚酯型TPU | ||||||
| 400系列 | ||||||
| ☆硬度：shore A85-shore A98 | ||||||
| ☆工艺：可挤出，流延 | ||||||
| ☆特性：良好的物理性能和稳定的加工性能，透明度好、性价比高 ☆应用：气动管、异形带、松紧带等 | ||||||
| 物理性质 | 检测标准 | 单位 | 485 | 490 | 495 | 498 |
| 比重 | SO1183-1:2004(E) | g/cm³ | 1.18 | 119 | .20 | 1.21 |
| 硬度 | ISO868:2003(E) | Shore AD | 85±2/ | 90±2/ | 95±2/ | 98±2/ |
| 00%抗拉模数 | ISO 37:2005(E) | MPa | 5 | 8 | 11 | 16 |
| 300%抗拉模数 | ISO37:2005(E) | MPa | 10 | 15 | 23 | 28 |
| 抗拉强度 | ISO 37:2005(E) | MPa | 28 | 32 | 35 | 40 |
| 伸长率 | ISO 37:2005(E) | % | 600 | 500 | 450 | 380 |
| 撕裂强度 | ISO34-1:2004(E) | KN/M | 90 | 115 | 135 | 160 |
| 磨耗 | DIN53516 | mg | 38 | 42 | 57 | 65 |
| 加工温度 | C | 170-190 | 175-195 | 180-200 | 185-205 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | ||||||
| POLYESTER-BASED TPU | ||||||
| 400 series | ||||||
| ☆ Hardness:Shore A85-ShoreA98 | ||||||
| ☆ Processing Methods:Extrusion,T-die extrusion | ||||||
| ☆Features: Good physical properties,Good Extrusion stability,High transparency ☆ Application: Air tube,Profiled tube,Bar tape and elstic. | ||||||
| Physical properties | Testing standard | Unit | 485 | 490 | 495 | 498 |
| Specific gravty | ISO1183-1:2004(E) | g/cm³ | 1.18 | 1.19 | .20 | 1.21 |
| Hardness | SO868:2003(E) | Shore AD | 85±2/ | 90±2/ | 95±2/ | 98±2/ |
| Tensile strength at 100%elongation | ISO37:2005(E) | MPa | 5 | 8 | 11 | 16 |
| Tensile strength at 300%elongation | ISO37:2005(E) | MPa | 10 | 15 | 23 | 28 |
| Tensile strength | ISO37:2005(E) | MPa | 28 | 32 | 35 | 40 |
| UItimate elongation | ISO37:2005(E) | % | 600 | 500 | 450 | 380 |
| Tear strength | iSO34-1:2004(E) | KN/M | 90 | 115 | 135 | 160 |
| Abrasion loss | DIN53516 | mg | 38 | 42 | 57 | 65 |
| Processing temperature | C | 170-190 | 175-195 | 180-200 | 185-205 | |
| ☆ These are typical values and should not be sued as specifications. | ||||||
金穗 聚酯型TPU 1100系列
| 聚 酯 型TPU | ||||||||||
| 1100系列 | ||||||||||
| ☆硬度：shore A70-shore D64 | ||||||||||
| ☆工艺：可注塑、挤出、压延 | ||||||||||
| ☆特性：物性优，耐磨性好，成型快 | ||||||||||
| 六应用：鞋材、轮子、玩具、表带、密封件、耳标、异形带等 | ||||||||||
| 物理性质 | 检测标准 | 单位 | 1170 | 1175 | 1180 | 1185 | 1190 | 1195 | 1198 | 1164 |
| 比重 | ISO1183-1:2004(E) | g/cm³ | 1.17 | 1.18 | 1.18 | 1.19 | 1.19 | 1.20 | 1.21 | 1.22 |
| 硬度 | ISO868:2003(E) | Shore A/D | 70±2/ | 75±2 | 80±2/ | 85±2/ | 90±2/ | 95±2/ | 98±2/ | 64±2 |
| 100%抗拉模数 | ISO37:2005(E) | MPa | 4.5 | 4.8 | 5 | 6 | 9 | 12 | 17 | 25 |
| 300%抗拉模数 | ISO37:2005(E) | MPa | 7.5 | 8 | 9 | 12 | 19 | 28 | 32 | 40 |
| 抗拉强度 | ISO37:2005(E) | MPa | 25 | 28 | 30 | 37 | 42 | 43 | 44 | 45 |
| 伸长率 | ISO37:2005(E) | % | 650 | 600 | 600 | 550 | 450 | 400 | 350 | 320 |
| 撕裂强度 | ISO34-1:2004(E) | KN/M | 78 | 80 | 90 | 100 | 125 | 145 | 170 | 220 |
| 磨耗 | DIN53516 | mg | 20 | 22 | 25 | 28 | 35 | 47 | 57 | 60 |
| 加工温度 | ℃ | 170-190 | 175-195 | 180-200 | 185-205 | 190-210 | 195-215 | 195-215 | 200-220 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | ||||||||||
| POLYESTER-BASED TPU | ||||||||||
| 1100 series | ||||||||||
| ☆Hardness: Shore A70-Shore D64 | ||||||||||
| ☆ Processing Methods: Injection,Extrusion,Calender | ||||||||||
| ☆Features:E xcellent physical properties,Good abrasion resistance,Fast formability | ||||||||||
| ☆ Application:Shoe sole,Wheel,Toys,Watch strap,Seal. | ||||||||||
| Physical properies | Testing standard | Unit | 1170 | 1175 | 1180 | 1185 | 1190 | 1195 | 1198 | 1164 |
| Specificgravity | ISO1183-12004(E) | g/cm³ | 1.17 | 1.18 | 1.18 | 1.19 | 1.19 | 120 | 1.21 | 1.22 |
| Hardness | ISO868:2003(E) | Shore A/D | 70±2 | 75±2/ | 80±2/ | 85±2/ | 90±2 | 95±2 | 98±2 | /64±2 |
| Tensile strength at 100%elongation | ISO37:2005(E) | MPa | 4.5 | 4.8 | 5 | 6 | 9 | 12 | 17 | 25 |
| Tensile strength at 300%elongation | SO37:2005(E) | MPa | 7.5 | 8 | 9 | 12 | 19 | 28 | 32 | 40 |
| Tensile strength | ISO37:2005(E) | MPa | 25 | 28 | 30 | 37 | 42 | 43 | 44 | 45 |
| Utmate elongation | ISO37:2005(E) | % | 650 | 600 | 600 | 550 | 450 | 400 | 350 | 320 |
| Tear strength | SO34-12004(E) | KN/M | 78 | 80 | 90 | 100 | 125 | 145 | 170 | 220 |
| Abrasion loss | DIN53516 | mg | 20 | 22 | 25 | 28 | 35 | 47 | 57 | 60 |
| Processing temperature | ℃ | 70-190 | 75-195 | 80-200 | 85-205 | 90-210 | 195-215 | 95-215 | 200-220 | |
| ☆ These are typical values and should not be sued as specifications. | ||||||||||
金穗 聚酯型TPU 1400系列
| 聚 酯 型TPU | ||||||
| 1400系列 | ||||||
| ☆硬度：shoreA85-shoreA98 | ||||||
| ☆工艺：可注望、挤出 | ||||||
| ☆特性：良好的物理性能和稳定的加工性能，成型快、性价比高 ☆应用：鞋材、轮子、手机壳、同步带等 | ||||||
| 物理性质 | 检测标准 | 单位 | 1485 | 1490 | 1495 | 1498 |
| 比重 | ISO1183-12004(E) | g/cm³ | 1.18 | 1.19 | 1.20 | 1.21 |
| 硬度 | ISO868:2003(E) | Shore A/D | 85±2/ | 90±2/ | 95:2/ | 98±2/ |
| 100%抗拉模数 | ISO37:2005(E) | MPa | 5 | 8 | 11 | 16 |
| 300%抗拉模数 | ISO37:2005(E) | MPa | 10 | 15 | 23 | 28 |
| 执校强度 | ISO37:2005(E) | MPa | 28 | 32 | 35 | 40 |
| 伸长率 | SO 37:2005(E) | % | 550 | 450 | 400 | 350 |
| 撕裂强度 | SO34-12004(日) | KN/M | 90 | 115 | 135 | 160 |
| 磨耗 | DIN53516 | mg | 35 | 40 | 55 | 60 |
| 加工温度 | ℃ | 170-190 | 175-195 | 180-200 | 185-205 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | ||||||
| POLYESTER-BASED TPU | ||||||
| 1400 series | ||||||
| ★Hardness:Shore A85-Shore A98 | ||||||
| Processing Methods: Injection extrusion | ||||||
| ☆Features:Good physical properties,Good Extrusion stabilily,Fast formablily,Low cost Appllcation: Shoe,Wheel,Cell phone cover,Timing belt,etc. | ||||||
| Physical proporties | Tosting standard | Unit | 1485 | 1490 | 1495 | 1498 |
| Specfc gravly | ISO1183-1:2004(E) | g/cm³ | 1.18 | 1.19 | 1.20 | 1.21 |
| Hardness | SO868:2003(E) | Shore A/D | 85±2/ | 90±2/ | 95±2/ | 98±2/ |
| Tensle strength at 100%elongaton | iSO 37:2005(E) | MPa | 5 | 8 | 11 | 16 |
| Tensle strength at 300%elongation | ISO 37:2005(E) | MPa | 10 | 15 | 23 | 28 |
| Tensile strength | SO37:2005(E) | MPa | 28 | 32 | 35 | 40 |
| UItmate elongation | SO 37:2005(E) | % | 550 | 450 | 400 | 350 |
| Tear strength | ISO34-1:2004(E) | KN/M | 90 | 115 | 135 | 160 |
| Abrasion loss | DIN53516 | mg | 35 | 40 | 55 | 60 |
| Procossing temperature | ℃ | 170-190 | 175-195 | 180-200 | 185-205 | |
| These are typical values and should not be sued as specifications. | ||||||
金穗 聚己内酯型TPU 1500系列
| 聚己内酯型TPU 1500系列 | |||||||
| ☆硬度：shore A80-shore A98 | |||||||
| ☆工艺：可注塑、挤出 | |||||||
| ☆特性：较好的耐油耐水解性、高耐磨性、低压缩永久形变、低温柔韧性 | |||||||
| ☆ 应用：电梯轮、密封件、电缆护套等 | |||||||
| 物理性质 | 检测标准 | 单位 | 1580 | 1585 | 1590 | 1595 | 1598 |
| 比重 | ISO1183-1:2004(E) | g/cm³ | 1.18 | 1.19 | 1.19 | 1.20 | 1.21 |
| 硬度 | SO868:2003(E) | Shore A/D | 80±2/ | 85±2/ | 90±2/ | 95±2/ | 98±2/ |
| 100%抗拉模数 | SO 37:2005(E) | MPa | 5 | 6 | 9 | 11 | 15 |
| 300%抗拉模数 | SO 37:2005(E) | MPa | 9 | 10 | 15 | 20 | 29 |
| 抗拉强度 | iSO 37:2005(E) | MPa | 27 | 29 | 32 | 34 | 35 |
| 伸长率 | ISO37:2005(E) | % | 570 | 530 | 440 | 400 | 380 |
| 撕裂强度 | SO34-1:2004(E) | KN/M | 110 | 120 | 130 | 135 | 140 |
| 加工温度 | ℃ | 180-200 | 185-205 | 190-210 | 195-215 | 195-215 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | |||||||
| POLYCAPROLACTONE-BASED TPU 1500 series | |||||||
| ☆Hardness: ShoreA85-ShoreA98 | |||||||
| ☆Processing Methods: Injection extrusion | |||||||
| ☆Features: Good oil resistance&Hydrolytic stability,Good abrasion resistance | |||||||
| Low compression set,Low temperature flexibity | |||||||
| ☆ Application:Elevator wheel,Seal,Wire &cable cover | |||||||
| Physical properties | Testing standard | Unit | 1580 | 1585 | 1590 | 1595 | 1598 |
| Speofic gravity | ISO1183-1:2004(E) | g/cm3 | 1.18 | 1.19 | 1.19 | 1.20 | 1.21 |
| Hardness | SO868:2003(E) | Shore A/D | 80±2/ | 85±2/ | 90±2/ | 95±2/ | 98±2/ |
| Tensile strength at 100%elongation | ISO37:2005(E) | MPa | 5 | 6 | 9 | 11 | 15 |
| Tensile strength at 300%elongation | SO37:2005(E) | MPa | 9 | 10 | 15 | 20 | 29 |
| Tensie strength | ISO37:2005(E) | MPa | 27 | 29 | 32 | 34 | 35 |
| Ultimate elongaton | ISO37:2005(E) | % | 570 | 530 | 440 | 400 | 380 |
| Tear strength | iSO34-1:2004(E) | KN/M | 110 | 120 | 130 | 135 | 140 |
| Prooessing temperature | ℃ | 180-200 | 185-205 | 190-210 | 195-215 | 195-215 | |
| These are typical values and should not be sued as specifications. | |||||||
金穗 聚酯型TPU 1600系列
| 聚 酯 型TPU 1600系 列 | ||||||
| ☆硬度：shoreA90-shore D64 | ||||||
| ☆工艺：可注塑、挤出 | ||||||
| ☆特性：透明度高，耐磨性好，稳定性佳 | ||||||
| ☆应用：轮子、玩具、鞋材、汽车配件、电线等 | ||||||
| 物理性质 | 检测标准 | 单位 | 1690 | 1695 | 1698 | 1664D |
| 比重 | SO1183-1:2004(E) | g/cm³ | 1.19 | 1.20 | 1.21 | 1.22 |
| 硬度 | ISO868:2003(E) | Shore A/D | 90±2/ | 95±2/ | 98±2/ | /64±2 |
| 100%抗拉模数 | ISO 37:2005(E) | MPa | 9 | 12 | 17 | 25 |
| 300%抗拉模数 | ISO 37:2005(E) | MPa | 19 | 28 | 32 | 40 |
| 抗拉强度 | ISO 37:2005(E) | MPa | 42 | 43 | 44 | 45 |
| 伸长率 | ISO 37:2005(E) | % | 450 | 400 | 350 | 320 |
| 撕裂强度 | SO34-1:2004(E) | KN/M | 125 | 145 | 170 | 220 |
| 磨耗 | DIN53516 | mg | 35 | 47 | 57 | 60 |
| 加工温度 | ℃ | 190-210 | 195-215 | 195-215 | 200-220 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | ||||||
| POLYESTER-BASED TPU 1600 series | ||||||
| ☆Hardness: Shore A90-Shore D64 | ||||||
| ☆Processing Methods: Injection extrusion | ||||||
| ☆Features:High transparency,Good abrasion resistance,Hydrolytic stability | ||||||
| ☆Application:Wheel,Air cushion,Shoe sole,Auto parts,Wire etc. | ||||||
| Physical properties | Testing standard | Unit | 1690 | 1695 | 1698 | 1664D |
| Specfic gravity | ISO1183-1:2004(E) | g/cm3 | 1.19 | 1.20 | 1.21 | 1.22 |
| Hardness | SO868:2003(E) | Shore AD | 90±2/ | 95±2/ | 98±2/ | /64±2 |
| Tensile strength at 100%clongaton | ISO 37:2005(E) | MPa | 9 | 12 | 17 | 25 |
| Tensile strength at 300%elongaton | ISO 37:2005(E) | MPa | 19 | 28 | 32 | 40 |
| Tenslle strength | ISO 37:2005(E) | MPa | 42 | 43 | 44 | 45 |
| UItimate elongaton | ISO 37:2005(E) | % | 450 | 400 | 350 | 320 |
| Tear strength | ISO34-1:2004(E) | KN/M | 125 | 145 | 170 | 220 |
| Abrasion loss | DIN53516 | mg | 35 | 47 | 57 | 60 |
| Prooessing temperature | ℃ | 190-210 | 195-215 | 195-215 | 200-220 | |
| These are typical values and should not be sued as specifications. | ||||||
金穗 聚酯型TPU 2100系列
| 聚酯型TPU 2100系列 | |||||||
| ☆硬度：shore A80-shore A98 | |||||||
| ☆工艺：吹塑、挤出、流延 | |||||||
| ☆特性：稳定性好，透明度好，耐磨性强 | |||||||
| ☆应用：薄膜、户外用具、鞋服等 | |||||||
| 物理性质 | 检测标准 | 单位 | 2180 | 2185 | 2190 | 2195 | 2198 |
| 比重 | ISO1183-1:2004(E) | g/cm³ | 1.18 | 1.19 | 1.19 | 1.20 | 1.21 |
| 硬度 | SO868:2003(E) | Shore A/D | 80±2/ | 85±2/ | 90±2/ | 95±2/ | 98±2/ |
| 100%抗拉模数 | ISO 37:2005(E) | MPa | 5 | 6 | 9 | 12 | 17 |
| 300%抗拉模数 | iSO 37:2005(E) | MPa | 9 | 12 | 19 | 28 | 32 |
| 抗拉强度 | iSO37:2005(E) | MPa | 30 | 37 | 42 | 43 | 44 |
| 伸长率 | ISO 37:2005(E) | % | 600 | 550 | 450 | 400 | 350 |
| 撕裂强度 | SO34-1:2004(E) | KN/M | 90 | 100 | 125 | 145 | 170 |
| 磨耗 | DIN53516 | mg | 25 | 28 | 35 | 47 | 57 |
| 加工温度 | ℃ | 180-200 | 185-205 | 190-210 | 195-215 | 195-215 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | |||||||
| POLYESTER-BASED TPU 2100 series | |||||||
| ☆Hardness: Shore A85-Shore A98 | |||||||
| ☆Processing Methods: Blow molding,Extrusion,Flow-casting | |||||||
| ☆ Features: High transparency,Good abrasion resistance,Hydrolytic stability | |||||||
| ☆ Application:Film,Outdoor peoducts,Shoes,Clothes etc. | |||||||
| Physical properties | Testing standard | Unit | 2180 | 2185 | 2190 | 2195 | 2198 |
| Specfic gravity | ISO1183-1:2004(E) | g/cm³ | 1.18 | 1.19 | 1.19 | 1.20 | 1.21 |
| Hardness | iSO868:2003(E) | Shore A/D | 80±2/ | 85±2/ | 90±2/ | 95±2/ | 98±2/ |
| Tensile strength at 100%elongation | ISO372005(E) | MPa | 5 | 6 | 9 | 12 | 17 |
| Tensile strength at 300%elongation | SO37:2005(E) | MPa | 9 | 12 | 19 | 28 | 32 |
| Tensile strength | iSO37:2005(E) | MPa | 30 | 37 | 42 | 43 | 44 |
| UItimate elongaton | SO37:2005(E) | % | 600 | 550 | 450 | 400 | 350 |
| Tear strength | iSO34-1:2004(E) | KN/M | 90 | 00 | 125 | 145 | 170 |
| Abasion losS | DIN53516 | mg | 25 | 28 | 35 | 47 | 57 |
| Prooessing temperature | ℃ | 180-200 | 185-205 | 190-210 | 195-215 | 195-215 | |
| ☆ These are typical values and should not be sued as specificatons. | |||||||
金穗 聚醚型TPU 3100系列
| 聚 醚 型TPU | ||||||
| 3100系 列 | ||||||
| ☆硬度：shore A80-shore A95 | ||||||
| ☆工艺：可注塑、挤出、流延 | ||||||
| ☆特性：耐水解、耐低温、耐霉菌性佳 | ||||||
| ☆应用：薄膜、花园管、动物耳标、玩具、线缆护套等 | ||||||
| 物理性质 | 检测标准 | 单位 | 3180 | 3185 | 3190 | 3195 |
| 比重 | SO1183-1:2004(E) | g/cm³5 | 1.11 | 1.12 | 1.13 | 1.14 |
| 硬度 | ISO868:2003(E) | Shore A/D | 80±2/ | 85±2/ | 90±2/ | 95±2/ |
| 100%抗拉模数 | ISO37:2005(E) | MPa | 6 | 7 | 10 | 13 |
| 300%抗拉模数 | ISO 37:2005(E) | MPa | 10 | 12 | 15 | 19 |
| 抗拉强度 | ISO37:2005(E) | MPa | 25 | 28 | 30 | 32 |
| 伸长率 | ISO 37:2005(E) | % | 550 | 500 | 450 | 400 |
| 撕裂强度 | ISO34-1:2004(E) | KN/M | 78 | 85 | 105 | 115 |
| 玻璃化温度 | ASTMD 3418 | ℃ | -45 | -40 | -40 | -40 |
| 加工温度 | ℃ | 175-195 | 175-195 | 180-200 | 190-210 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | ||||||
| POLYETHER TYPE-BASED TPU | ||||||
| 3100 series | ||||||
| ☆ Hardness:Shore A85-ShoreA98 | ||||||
| ☆ Processing Methods: Injection extrusion,Flow-casting | ||||||
| ☆ Features:H ydrolytic stabiiy,Low temperature flexibility,Fungus resistance | ||||||
| ☆ Application: Film,Garden hose,Ear tag,Toy,Cable &Wire jectek etc. | ||||||
| Physlcal propertles | Testing standard | Unit | 3180 | 3185 | 3190 | 3195 |
| Specific gravity | ISO1183-1:2004(E) | g/cm³ | 1.11 | 1.12 | 1.13 | 1.14 |
| Hardness | SO868:2003(E) | Shore A/D | 80±2/ | 85±2/ | 90±2/ | 95±2/ |
| Tensile strength at 100%elongation | ISO 37:2005(E) | MPa | 6 | 7 | 10 | 13 |
| Tensile strength at 300%elongation | ISO 37:2005(E) | MPa | 10 | 12 | 15 | 19 |
| Tenslle strength | ISO37:2005(E) | MPa | 25 | 28 | 30 | 32 |
| UItimate elongation | ISO37:2005(E) | % | 550 | 500 | 450 | 400 |
| Tear strength | ISO34-1:2004(E) | KN/M | 78 | 85 | 105 | 115 |
| Vitrification temperature | ASTMD3418 | ℃ | -45 | -40 | -40 | -40 |
| Processing temperature | ℃ | 175-195 | 175-195 | 180-200 | 190-210 | |
| ☆ These are typical values and should not be sued as specifications. | ||||||
金穗 聚酯型TPU 2700系列
| 聚 酯 型TPU 2700系 列 | |||||||
| ☆硬度：shore A80-shore A98 | |||||||
| ☆工艺：可注塑、挤出、压延 | |||||||
| ☆特性：物性优，稳定性佳，透明度好，耐磨性好 | |||||||
| ☆应用：玩具、异形带、气动管、夹纱管、电线电缆、汽车配件等 | |||||||
| 物理性质 | 检测标准 | 单位 | 2780 | 2785 | 2790 | 2795 | 2798 |
| 比重 | ISO1183-1:2004(E) | g/cm³ | 1.18 | 1.19 | 1.19 | 1.20 | 1.21 |
| 硬度 | ISO868:2003(E) | Shore A/D | 80±2/ | 85±2/ | 90±2/ | 95±2/ | 98±2/ |
| 100%抗拉模数 | iSO37:2005(E) | MPa | 5 | 6 | 9 | 12 | 17 |
| 300%抗拉模数 | ISO 37:2005(E) | MPa | 9 | 12 | 19 | 28 | 32 |
| 抗拉强度 | ISO 37:2005(E) | MPa | 30 | 37 | 42 | 43 | 44 |
| 伸长率 | ISO 37:2005(E) | % | 600 | 550 | 450 | 400 | 350 |
| 撕裂强度 | ISO34-1:2004(E) | KN/M | 90 | 100 | 125 | 145 | 170 |
| 磨耗 | DIN53516 | mg | 25 | 28 | 35 | 47 | 57 |
| 加工温度 | ℃ | 180-200 | 185-205 | 190-210 | 195-215 | 195-215 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | |||||||
| POLYESTER-BASED TPU 2700 series | |||||||
| ☆ Hardness: ShoreA80-ShoreA98 | |||||||
| Processing Methods:Injection extrusion,Calender | |||||||
| ☆ Features: Good physical properties,Hydrolytic stability,High transparency,Good abrasion resistance ☆ Application: Toy,Profiled belt,Air tube,Cable &Wire,Auto parts | |||||||
| Physical properties | Testing standard | Unit | 2780 | 2785 | 2790 | 2795 | 2798 |
| Specific gravity | ISO1183-1:2004(E) | g/cm³ | 1.18 | 1.19 | 1.19 | 1.20 | 1.21 |
| Hardness | SO868:2003(E) | Shore A/D | 80±2/ | 85±2/ | 90±2/ | 95±2/ | 98±2/ |
| Tensile strength at 100%elongation | SO 37:2005(E) | MPa | 5 | 6 | 9 | 12 | 17 |
| Tensile strength at 300%elongation | ISO 37:2005(E) | MPa | 9 | 12 | 19 | 28 | 32 |
| Tensle strength | ISO 37:2005(E) | MPa | 30 | 37 | 42 | 43 | 44 |
| Ultimate elongation | SO 37:2005(E) | % | 600 | 550 | 450 | 400 | 350 |
| Tear strength | ISO34-1:2004(E) | KN/M | 90 | 100 | 125 | 145 | 170 |
| Abrasion loss | DIN53516 | mg | 25 | 28 | 35 | 47 | 57 |
| Prooessing temperature | ℃ | 180-200 | 185-205 | 190-210 | 195-215 | 195-215 | |
| These are typical values and should not be sued as specificatons. | |||||||
金穗 聚酯型TPU3600系列
| 聚 酯 型TPU3600系 列 | |||||||
| ☆硬度：shoreA70-shore A95 | |||||||
| ☆工艺：可挤出、刮涂、也可用溶剂溶解 | |||||||
| ☆特性：接着性佳，适用性强 | |||||||
| ☆应用：热熔胶膜、织物贴合、汽车工业等 | |||||||
| 物理性质 | 单位 | 3670 | 3675 | 3680 | 3685 | 3690 | 3695 |
| 硬度 | ShoreA | 70±2 | 75±2 | 80±2 | 85±2 | 90±2 | 95±2 |
| 起始流动温度 | ℃ | 95 | 100 | 120 | 95 | 110 | 100 |
| 热贴合温度 | ℃ | 120-140 | 130-150 | 140-160 | 120-140 | 130-150 | 120-140 |
| 表干时间 | Min. | 10 | 6 | 15 | 6 | 8 | 10 |
| 注：以上数值仅为典型值，不可视为产品标准。 | |||||||
| POLYESTER-BASED TPU 3600 series | |||||||
| ☆Hardness: ShoreA70-ShoreA95 | |||||||
| ☆Processing Methods:T-die extrusion,Melt processing,coating. | |||||||
| ☆ Features: Outstanding bonding strength for fabric,Leather,Plastics&Rubber,Wood,etc. ☆Application:Hot-melt Adhesive film.Fabric laminated. | |||||||
| Physical properies | Unit | 3670 | 3675 | 3680 | 3685 | 3690 | 3695 |
| Hardness | ShoreA | 70±2 | 75±2 | 80±2 | 85±2 | 90±2 | 95±2 |
| Flow beginring temperature | ℃ | 95 | 100 | 120 | 95 | 110 | 100 |
| Suggesled bondng temperature | ℃ | 120-140 | 130-150 | 140-160 | 120-140 | 130-150 | 120-140 |
| Tack-free time | Min | 10 | 6 | 15 | 6 | 8 | 10 |
| ☆ These are typical values and should not be sued as specifications. | |||||||
金穗 聚酯型TPU 2400系列
| 聚酯型TPU 2400系 列 | ||||||
| 工艺：可挤出，流延 | ||||||
| 特性：良好的物理性能和稳定的加工性能，透明度好、性价比高 应用：气动管、异形带等 | ||||||
| 应用：气动管、异形带等 | ||||||
| 物理性质 | 检测标准 | 单位 | 2485 | 2490 | 2495 | 2498 |
| 比重 | ISO1183-1:2004 | g/cm³ | 1.25 | 1.24 | 1.24 | 1.25 |
| 硬度 | IS0868:2003 | ShoreA/D | 85A±2 | 90A±2 | 95A±2 | 98A±2 |
| 100%抗拉模数 | ISO37:2005 | MPa | 70 | 107 | 114 | 163 |
| 300%抗拉模数 | ISO37:2005 | MPa | 114 | 160 | 171 | 239 |
| 抗拉强度 | ISO37:2005 | MPa | 257 | 286 | 295 | 343 |
| 伸长率 | SO37:2005 | % | 723 | 618 | 603 | 558 |
| 撕裂强度 | ISO34-1:2004 | KN/M | 111 | 152 | 150 | 186 |
| 磨耗 | DIN53516 | mg | ||||
| 加工温度 | ℃ | 200 | 205 | 205 | 210 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | ||||||
| POLYESTER-BASEDTPU | ||||||
| 2400 series | ||||||
| Hardness:shoreA85-shoreA98 | ||||||
| Processing Methods: Extrusion,T-die extrusion | ||||||
| Features:Good physical properties,Good Extusion stabilit,High transparency | ||||||
| Application:Air tube,Profled tube | ||||||
| Physical properties | Testing standard | Unit | 2485 | 2490 | 2495 | 2498 |
| Specific gravity | ISO1183-1:2004 | g/cm3 | 1.25 | 1.24 | 1.24 | 1.25 |
| Hardness | ISO868:2003 | ShoreAD | 85A±2 | 90A±2 | 95A±2 | 98A±2 |
| Tensile strength at 100%elongation | iS037:2005 | MPa | 70 | 107 | 114 | 163 |
| Tensle strength at 300%elongation | iSO37:2005 | MPa | 114 | 160 | 171 | 239 |
| Tensile strength | ISO37:2005 | MPa | 257 | 286 | 295 | 343 |
| UItimate elongation | ISO37:2005 | % | 723 | 618 | 603 | 558 |
| Tear strength | ISO34-1:2004 | KN/M | 111 | 152 | 150 | 186 |
| Abrasion loss | DIN53516 | mg | ||||
| Processing temperature | ℃ | 200 | 205 | 205 | 210 | |
| These are typica values and should not be sued as specifications. | ||||||
金穗 聚酯型TPU 1100A 系列
| 聚酯型TPU 1100A 系列 | |||||
| 合硬度：shore A55~shore A70 | |||||
| 工艺：可注塑，挤出，流延 | |||||
| 特性：物性优，成型快 | |||||
| 合应用：可注塑，鞋底，玩具，汽车配件等 | |||||
| 物理性质 | 检测标准 | 单位 | 1155A | 1160A | 1165A |
| 比重 | ISO1183-1:2004 | g/cm³ | 1.18 | 1.18 | 1.19 |
| 硬度 | SO868:2003 | ShoreA/D | 55A±2 | 60A±2 | 65A±2 |
| 100%抗拉模数 | ISO37:2005 | MPa | 18 | 19 | 22 |
| 300%抗拉模数 | ISO37:2005 | MPa | 30 | 33 | 36 |
| 抗拉强度 | SO37:2005 | MPa | 189 | 125 | 156 |
| 伸长率 | ISO37-2005 | % | 1063 | 961 | 1039 |
| 撕裂强度 | ISO34-1:2004 | KN/M | 57 | 58 | 61 |
| 磨耗 | DIN53516 | mg | 168 | 233 | 214 |
| 加工温度 | ℃ | 160 | 170 | 170 | |
| 注：以上数值仅为典型值，不可视为产品标准。 | |||||
| POLYESTER-BASED TPU 1100A series | |||||
| 合 Hardness:shore A55~shore A70 | |||||
| Processing Methods: Injection, Extrusion, Calender | |||||
| Features: Excellent physical properties, Fast formability | |||||
| Application: Air tube, Profiled tube | |||||
| Physical properties | Testing standard | Unit | 1155A | 1160A | 1165A |
| Specific gravity | SO1183-1:2004 | g/cm³ | 1.18 | 1.18 | 1.19 |
| Hardness | ISO868:2003 | ShoreA/D | 55A±2 | 60A±2 | 65A±2 |
| Tensile strength at 100%elongation | ISO37:2005 | MPa | 18 | 19 | 22 |
| Tensile strength at 300%elongation | ISO37:2005 | MPa | 30 | 33 | 36 |
| Tensile strength | ISO37:2005 | MPa | 189 | 125 | 156 |
| Ultimate elongation | ISO37:2005 | % | 1063 | 961 | 1039 |
| Tear strength | ISO34-1:2004 | KN/M | 57 | 58 | 61 |
| Abrasion loss | DIN53516 | mg | 168 | 233 | 214 |
| Processing temperature | ℃ | 160 | 170 | 170 | |
| These are typical values and should not be sued as specifications. | |||||
金穗 聚酯型TPU 1100D系列
| 聚酯型TPU 1100D系列 | ||||||
| shore D70-shore D85 | ||||||
| 可注塑，挤出 | ||||||
| 物性优，强度高，成型快 | ||||||
| 油杯，鞋中腰等 | ||||||
| 物理性质 | 检测标准 | 单位 | 1172D | 1175D | 2770D | 1685D |
| 比重 | ISO1183-1:2004 | g/cm3 | 1.24 | 1.24 | 1.24 | 1.25 |
| 硬度 | ISO868:2003 | ShoreA/D | 72D±2 | 75D±2 | 70D±2 | 85D±2 |
| 100%抗拉模数 | ISO37:2005 | MPa | 277 | 369 | 319 | 381 |
| 300%抗拉模数 | iSO37:2005 | MPa | 320 | 382 | 360 | 433 |
| 抗拉强度 | ISO37:2005 | MPa | 338 | 426 | 393 | 718 |
| 伸长率 | ISO37:2005 | % | 442 | 436 | 413 | 69 |
| 撕裂强度 | SO34-1:2004 | KN/M | 225 | 310 | 280 | |
| 磨耗 | DIN53516 | mg | 85 | |||
| 加工温度 | ℃ | 220 | 225 | 220 | 225 | |
| 注：以上数值仅为典型值，不可视为产品标准。 These are typical values and should not be sued as specifications. | ||||||
| 産品注意事项 |
| 储存 |
| TPU是一种吸湿性很强的树脂，且吸湿的TPU会给TPU的成型与加工带来不利影响，因此，TPU 必须密闭于干燥、阴凉处储存，开袋产品应置于干燥器内。严禁袋装TPU产品与水接触或放置于温度较高的场所，开袋后的产品严禁长时间露天放置。一旦出现类似情况，吸湿程度较低的可延长干燥时间，若吸湿程度较高则不能够再使用，应做为废料处理。 |
| 安全 |
| 人体一般不会对TPU产品产生过敬，如果接触TPU原料或产品感到不适，应该停止与TPU原料或产品接触，严重时应该立即就医。在加工过程中，应避免身体各部位与熔融TPU 或高温TPU 制成品直接接触，以防被烫伤；且应避免吸入TPU 高温分解蒸气，加工厂房应该保持局部通风与机械通风，以防吸入有害气体。 |
| 燃烧爆炸危害 |
| KINGSUI°TPU 产品的理论闪点值超过250℃,危险分解物为一氧化碳、异氤酸酯蒸汽、微量氰化氢气体。 KINGSUI°TPU 几乎没有爆炸危害，但在加热或明火时有火灾危害，灭火可采用水、沙子或二氧化碳气体，灭火人 员必须穿戴防一氧化碳、二氧化碳气体的防护用品。 |
| 环保 |
| 根据环保法规规定，TPU 为正常废弃物，如果允许可以进行掩埋、焚烧处理。 |
| KINGSUI®TPU 包装物为纸和塑料，使用完后应对废弃包装物进行分类回收，防止资源浪费与环境污染。 |
| PRODUCT NOTICE |
| STORAGE Prolonged contact with water can lead to hydrolysis of certan types of TPU resins because of its high mois-ture absorbing property.For this reason,it must be stored in tightly closed containers in adry,cool and shady area.Never make TPU be contacted with water,nor put them at humld locations.Never put opened packages in open airfor proonged periods of time.During processing,moisture in TPU resins wilead to degradation and defective finished products,soitis recommended to remove moisture to make its content below 0.03% prior to processing. |
| SAFETY It is possible that someone s allergic to TPU,ifso,please stop contacting with raw material or fnished products immediately.With severe cases,call for prompt medical care. During processing,avoid direct contact with melting TPU or finished produc at high temperature to prevent scald.Avoid inhalation of decomposition vapor at high temperature.Local and mechanical ventilation in workshopsis amust so as to prevent inhalation of hazardous gas. |
| HAZARDS OF COMBUSTION AND EXPLOSION |
| The theoretical flash point of TPU products is over 250℃.Hazardous decompositon products:include CO,isocyanate vapor,trace amount of hydrogen cyanide gas(if combusted). This product poses almost no danger of explosion.However,when heated or exposed to fames,it may cause fire.Extinguishing media may be water,sand,or co₂.Fire fighting personnel must be equipped with personal protection devices against CO and CO₂ |
| ENVIRONMENT |
| Splled pellets must be cleared up.According to environmental laws and regulations,TPU are common non-controlled wastes,which means they can be buried or combusted under permission. Classification and recovery of TPU packages made of paper and plastics after use is recommended to avoid wastes of resources and environmental pollution. |
另：有部分抗UV，防静电等型号定制牌号。详情请联系塑能
（免责声明：本数据采集自网络，仅供参考，非标准值，如有疑问，请联系厂家，以厂家官方说明为准。本资料版权归原作者所有，如有侵权，请联系删除）
可提供的报告：
TDS-ASTM（美国标准测试物性表），RoHS（环保报告），SVHC，COA（出厂质量检测报告）
Email:info@plaspowers.com
www.plaspowers.com
sister corporation:Sunengtag
Wechat: sunengpv
评价
目前还没有评价